Jeld-Wen Siteline Ex Clad Casement

Siteline Ex Clad Casement - Vertical Section

Siteline Ex Clad - Horizontal Section

Siteline Ex Clad Casement - Stationary Vertical Section

Siteline Ex Clad Casement - Stationary Horizontal Section

Standard Widths:

Standard Heights:

Book Code Example: ECC1818

ECC = Siteline EX Clad CSMT
First 2 #'s = Frame Width
Last 2 #'s = Frame Height

Hardware

H2 = Casement Hinge Track

LH Casement Hinge Track - used on lower left or upper right
RH Casement HInge Track - used on upper left or lower right 

• H2 = LH Casement HInge Track #WN401
• H2 = RH Casement Hinge Track #WN402

For Service use only:

• H2 = LH Casement Adj. Hinge Track #W02V2
• H2 = RH Casement Adj. Hinge Track # W02V3

H3 Casement Dual Arm Operator

H3 = LH & RH Dual Arm Operators - 20" or greater widths

• Left Hand - #W00KR
• Right Hand - #W00KS

H3 = LH & RH Arm Operators - 19 15/16" or less widths

• Left Hand - #WJ633
• Right Hand #WJ634

Handle Receivers = Silver (LH), Gold (RH)

H4 Casement Folding Handle W/Operator Cover

Black Construction Handle & Crank - W4522

Operational Handsets

Round Handle/Cover Package

T Handle/Cover Package

H3 Radius Casements

Radius Casement LH & RH Casement Single Arm Operator

H3 LH Single Arm Operator Bracket - WK265
H3 RH Single Arm Operator Bracket - WK266

Friction Control Device:
Larger than 24" width - W00LD
24" and smaller width - W00LE

Radius Casement LH & RH Butt Hinge

LH - WK264
RH - WK263

Viewed from exterior

Hinge to Sash Screw
Clad & Prime - WN384 #8 x 1 1/4"

Hinge to Frame Screws
Clad - W0350 #7 x 1/2"
Prime - 776797 #7 x 5/8"

H5 Casement Sash Track

Part number - WJ632

H7 Casement Lock Handle & Escutcheon

H6 LH & RH Split/Dual Arm Operator Bracket

Split Arm Operator Bracket

LH Split Arm Operator Bracket - WJ635
RH Split Arm Operator Bracket - WJ636

*Used for 19 7/8" and under operators

Dual Arm Operator Bracket

LH Dual Arm Operator Bracket - WJ628
RH Dual Arm Operator Bracket - WJ630

*Used for 20" and over operators

H8 Casement Sash Keepers

WO497

H9 Casement Lock Bar Drive Assembly & Lock Bar

Lock Bar Drive Assembly: W0503

Lock Bar Guides: W0474

Lock Bar - Window Height:

H10 Sash & Frame Snubber

WO494

H11 Picture & Stationary Sash Installation Bracket

W0498

Sash Limiter Installation

Ex Csmt Sash Limiter: W0475

Bottom Frame Hinge Track

Top Frame Hinge Track

Installation

The sash limiter is installed to the frame hinge track on both the top and bottom. You will need to remove the screw in the center location of the track, followed by removing the hinge arms. Next slide the sash to the hinge side as much as possible. Slide the limiter into the track then reinstall the screw into the frame hinge track. Reconnect the hinges to the stud posts and install the operator into the track. The sash should now be limited with the black plastic shoe stopped behind the sash limiter piece.

Sash Limiter Clear Opening Specifications

Sash Limiter: WO475

Installation & Operating Instructions

for Casement Window Opening Control Devices (Jll038)

Thoroughly read these instructions and understand the operation of this device. failure to follow instructions may result in injury or death.

The window opening control device is designed to limit the opening of the window so that objects no larger than a 4: rigid sphere will fit through the opening. This is to protect against accidental falls from an open window, but is not a substitute for traditional safety practices. Train all occupants 6 years old and older to operate the release mechanism in case of an emergency. 

Important Information & Safety

• The window opening control device engages automatically when the window is closed. 
• Check for re-engagement of window opening control device after each release.
• Test once a month for proper operation and inspect for damage. Replace devie promptly if necessary.
• Make sure the device is properly installed, engaged, and operated as specified. Do no modify the device in any way.
• Make sure proper labeling and operating instructions are available to the homeowner/operator after installation is complete. Contact us for a copy of the safety informations. 
• Do not rely on being rescued from windows above 75 ft (6th floor). Follow building fire escape plan. 

Installation

Warning! Failure to properly install device may allow window to open unexpectedly causing falls through the window

Sash Preparation & Arm Attachment

1. Open sash. Using the provided template, mark screw hole locations for the bracket on the vertical section of sash in the same location as the hinge pocket. 
2. Pre-drill 3/32" screw holes 1/2" deep where marked.
3. Attach bracket in orientation shown, with two of the provided screws. 
4. Be sure arm moves freely and hangs toward the inside of the window at an approximate 20° angle from vertical. 

Frame Preparation & Sash Attachment

1. Position track on the vertical section of the frame in the same location as the hinge pocket against the sill in the position shown. Mark the track hole locations on the frame. 
2. Pre-drill 3/32" screw holes 1/2" deep where marked.
3. Attach track in orientation shown, with two of the provided screws. 
4. Operate window and verify device performs correctly. Immediately fix any problems.
5. Place the included label on the top of the operator housing between the crank arm and window frame or other visible location when the window is closed. 

Operation

To open window and release window opening control device

1. Unlock window and crank open to the limit. Back off slightly to release pressure and ease limiter operation. 
2. Slide cover up
3. Rotate tab toward the exterior and hold. Continue to crank open window until the arm is free from the track.

To close window and re-engage window opening control device:

1. Crank window all the way closed. The device will automatically reset at or near the fully closed position. 
2. To check for device engagement, crank open window until device limits the window opening. 

Prime Casement Sash Weatherstrip - 

All the Way Around 

WK776

W1 Clad Casement Sash Weatherstrip - Top Only 

WZ846

*Clad Only

W2 Clad Casement Sash Weatherstrip - Bottom & Sides

W00NN

*Clad Only

W3 Siteline EX & Classic 

Casement Foam Filled Frame Weatherstrip 

Prime & Clad

W0357

W4 Drip Cap Ex-Vinyl Clear - Narrow 

W0751
196" Lengths

17A Radius Casement - Sash Weatherstrip

(Dh Cl & PR Rail Foam)
WN940

Sash Weatherstrip (Radius Casements Only)

J1 Casement Operator Cover

Identifier Number - JWPC-103
Detail Number - CA0144OC

J2 Casement Operator Cover Support

Identifier Number - JWPC-104
Detail Number - CA0145OC

Dual Arm & DYAD Lengths - Lock Side

DUAL ARM & DYAD Lengths - Hinge Side
J54840

Single Arm Lengths - Hinge Side
J54848

Single Arm Lengths - Lock Side

J3 Casement Operator Cover Support Block

Identifier Number - JWPC-143
Detail Number - CA0227MS
Part Number: J13068
84"

J4 Casement/Awning Head Stop

Identifier Number - JWPC-102
Detail Number - CA0293SP

J5 Casement/Awning Side Stop - Operator

Awning
2 Side stops per operator unit
Note On Order: "Route for Lockside 1L-1R"

Casement
1 - Hinge Side - No pred needed Use Part #
1 - Lockside - Additional Route Needed
Note On Order: 
"Route for RH Unit Lockside"
"Route for LH Unite Lockside"

J6 Casement/Awning Head & Sill Stop - Stationary

Identifier Number - JWPC-107
Detail Number - CA0291SP

J7 Casement/Awning Side Stops - Stationary

Identifier Number - JWPC-107
Detail Number - CA0291SP

Window Operating Control Device (WOCD)

Left Hand - W07BV

Right Hand - W07BW

Drawings