Jeld-wen Siteline Ex Clad Double Hung Windows

Siteline Ex Clad Double Hung - Vertical Section 

Hardware Wood Parts Weatherstrip
H1 = Tilt Latch Button J1 = Head Parting Stop W1 = Parting Stop Weatherstrip
H2 = Tilt Latch Body W2 = Check Rail Weatherstrip
H3 = Sashlock W3 = Bottom Rail Weatherstrip
H4 = Tilt Latch Coverplate W4 = Sill Weatherstrip
H5 = Keeper w/ Protector

Classic Clad Double Hung - Vertical Section

Only 2 Differences from Ex Clad:
  • Classic has DP60 Sill
  • No Fingerplow
Hardware Wood Parts Wetherstrip
H1 = Tilt Latch Button J1 = Head Parting Stop W1 = Parting Stop Weatherstrip
H2 = Tilt Latch Body W2 = Check Rail Weatherstrip
H3 = Sashlock W3 = Bottom Rail Weatherstrip
H4 = Tilt Latch Coverplate W4 = Sill Weatherstrip
H5 = Keeper w/ Protector

Siteline Ex Clad Double Hung - Horizontal Section

Hardware Wood Parts Weatherstrip
H6 = Jamb Liner J2 = Side Liner Stop W5 = Jamb Liner Head Foam Pad
H7 = Pivot Bar W6 = Pock Plug-Doghouse
H8 = Screen Pin W7 = Dust Plug
H9 = Jamb Jack w/ Screw Part
H10 = Plastic Liner Stop/Cap
H11 = Jamb Liner Balances

Classic Clad Double Hung - Horizontal Section

Only 2 Differences from Ex Clad:
  • Classic has DP60 Sill
  • No Fingerplow
Hardware Wood Parts Weatherstrip
H6 = Jamb Liner J2 = Side Liner Stop W5 = Jamb Liner Head Foam Pad
H7 = Pivot Bar W6 = Pocket Plug-Doghouse
H8 = Screen Pin W7 = Dust Plug
H9 = Jamb Jack w/ Screw Part
H10 = Plastic Liner Stop/Cap
H11 = Jamb Liner Balances

Siteline Ex Clad Double Hung

Standard Widths

Sash Opening Sash Width Daylight Opening Glass
21 3/8" 20" 18 3/8" 14 13/16" 15 3/4"
25 3/8" 24" 22 3/8" 18 13/16" 19 3/4"
29 3/8" 28" 26 3/8" 22 13/16" 23 3/4"
31 3/8" 30" 28 3/8" 24 13/16" 25 3/4"
33 3/8" 32" 30 3/8" 26 13/16" 27 3/4"
37 3/8" 36" 34 3/8" 30 13/16" 31 3/4"
41 3/8" 40" 38 3/8" 34 13/16" 35 3/4"
45 3/8" 44" 42 3/8" 38 13/16" 39 3/4"

Standard Heights

Sash Opening Sash Heights Daylight Opening Glass
32" 30" Top: 15 3/16"
Btm: 15"
11 1/16" 12"
36" 34" Top: 17 3/16"
Btm: 17"
13 1/16" 14"
40" 38" Top:19 3/16"
Btm: 19"
15 1/16" 16"
44" 42" Top: 21 3/16"
Btm: 21"
17 1/16" 18"
48" 46" Top: 23 3/16"
Btm: 23"
19 1/16" 20"
52" 50" Top: 25 3/16"
Btm: 25"
21 1/16" 22"
56" 54" Top: 27 3/16"
Btm: 27"
23 1/16" 24"
60" 58" Top: 29 3/16"
Btm: 29"
25 1/16" 26"
64" 62" Top: 31 3/16"
Btm: 31"
27 1/16" 28"
68" 66" Top: 33 3/16"
Btm: 33"
29 1/16" 30"
72" 70" Top 35 3/16"
Btm: 35"
31 1/16" 32"
76" 74" Top: 37 3/16"
Btm: 37"
33 1/16" 34"
80" 78" Top: 39 3/16"
Btm: 39"
35 1/16" 36"
88" 86" Top: 43 3/16"
Btm: 43"
39 1/16" 40"
92"  90" Top: 45 3/16"
Btm: 45"
41 1/16" 42"

Siteline Ex Clad Double Hung


Book Code Example: ECD2140< ECD = Siteline Ex Clah DH
First 2#'s = Frame Width - 3/8"
Last 2 #'s = Frame Height

Vertical Section

Horizontal Section

Siteline Ex Clad Double Hung Picture - 

Vertical Section

Wood Parts Weatherstrip
J3 = Horizontal Sash Stop W3 = Top & Bottom Rail Weatherstrip
W4 = Sill Weatherstrip

Classic Clad Double Hung Picture - 

Vertical Section

Only Difference From Ex:
Classic has DP60 Sill
Wood Parts Weatherstrip
J3 = Horizontal Sash Stop W3 = Top & Bottom Rail Weatherstrip
W4 = Sill Weatherstrip

Siteline Ex Clad Double Hung Picture - Horizontal Section

Wood Parts Weatherstrip
J4 = Side Inside Stop W3 = Rail Weatherstrip
J5 = Side Liner Stop

Classic Clad Double Hung Picture - 

Horizontal Section

Only Difference From Ex:
Classic has DP60 Sill
Wood Parts Weatherstrip
J4 = Side Inside Stop W3 = Rail Weatherstrip
J5 = Side Liner Stop

H1,H2 - DH Operator Top Sash 

Tilt Latch Body & Button

H1 = DH Tilt Latch Button - Tan - W3076
H2 = DH Tilt Latch Body - Tan - WN405

H5 - DH Operator Sashlock & Keeper

Old Sashlock

*Running change implemented May 2014. Might need to replace multiple to match exisiting product

New Sashlock 

Finish H3 = DH Sashlock H5 = DH Keeper
Chestnut Bronze WK146 WK154
Brilliant White WK147 WK155
Polished Brass WK148 WK156
Desert Sand WK149 WK157
Antique Brass WK150 WK158
Brush Chrome WK151 WK159
Oil Rubbed Bronze WK152 WK160
Satin Nickel WK153 WK161

Installation Screws - w0atc

DH Operator Bottom Sash - 

Tilt Latch Body & Coverplate

Finish H4 = DH Coverplate
Chestnut Bronze W3081
Brilliant White W3371
Brass  W3375
Desert Sand W3379
Antique Brass WI444
Brushed Chrome WI445
Oil Rubbed Bronze WI446

H2 = DH Tilt Latch Body = WN405

H6 DH Operator Jambliner

H7 Double Hung Pivot Bars - Right & Left

Siteline EX Pivot Bars
Right - W3079
Left - W3078
Classic Zinc
Size Mount Pivot
W04UV

Clutch Classic Coil Style
*Used on Classic Clad DH units only (Any unit built after March 22, 2012) 68" - 80"

Standard Spring Balance

H8 DH Screen Plunger, Spring, and Cap

Part Number
Plunger - Prime W00KB
Plunger - Clad W00KP
Springs W00KC
Caps W00KD

H9 DH Jamb Jack w/ Screw

Part Number
Jamb Jack Nut WF587
Screw Pack & Instructions W3070

DH Plastic Sash Jambliner Stop

Part Number
Tan Sash Stop - 1 3/8" W3802
White Sash Stop - 1 3/8" W3799
Tan Sash Stop - 13 3/8"  W3803
White Sash Stop - 13 3/8" W3800
*Note 13 3/8" Stop is used for Cottage Style Units only

Old EX Intek Jambliner 

October 8, 2007 - February 8, 2010

Balance Cover (Tilt latch Receiver)
Lineal Part Numbers (12-0)
White - W1749
Beige - W1750

To order complete replacement jambliner enter through DH Generic. All complete jambliner ordered will be the new micron jambliner below. Complete jambliners sold in pairs only.

New EX Micron Jambliner

February 8, 2010 - Present

Tilt Latch Receiver
Lineal Part Numbers (13-0)
White - W038H
Tan - Tan W038I

Jambliner Bulb Weather
White - W038P
Tan - W038Q

Old Ex Intek 

Used from October 8, 2007 - February 8, 2010
Drawing: SLEX - 188

Assembly Instructions:

  1. Install standard jambliner with standard tilt latch receivers
  2. Install top sash
  3. Install top sash limiter (B) so that it protrudes away from the jambliner
  4. Lower the clutches for the bottom sash to within 2" of the sill
  5. Install bottom sash limiter in normal orientation as standard tilt latch receivers
  6. Install bottom sash
Double Hung Unit Height
Bottom Glass Height Bottom Sash Limiter Length (A) Top Sash Lmiter Length (B)
32 12 9 1/8 10 5/8
36 14 11 1/8 12 5/8
40 16 13 1/8 14 5/8
44 18 15 1/8 16 5/8
48 20 17 1/8 18 5/8
52 22 19 1/8 20 5/8
56 24 21 1/8 22 5/8
60 26 23 1/8 24 5/8
64 28 25 1/8 26 5/8
68 30 27 1/8 28 5/8
72 32 29 1/8 30 5/8
76 34 31 1/8 32 5/8
80 36 33 1/8 34 5/8
88 40 37 1/8 38 5/8
92 42 39 1/8 40 5/8

*Jeld-Wen Lineal Part Number - Wi749 (White) Wi750 (Beige)
 Intek Lineal Part Number - 21360AA (White) 21360AB (Beige)

New EX Micron

February 8, 2010 - Present

Assembly Instructions:

  1. Install standard jambliners with standard tilt latch receivers
  2. Install top sash
  3. Install top sash limiter (B) so that it protrudes away from the jambliner
  4. Lower the clutches for the bottom sash to within 2" of the sill
  5. Install bottom sash limiter in normal orientation as standard tilt latch receivers 
  6. Install bottom sash 

Double Hung Unit Height Bottom Glass Height Bottom Sash Limiter Length (A) Top Sash Limiter Length (B)
32 12 9 1/8 10 5/8
36 14 11 1/8 12 5/8
40  16 13 1/8 15 5/8
44 18 15 1/8 16 5/8
48 20 17 1/8 18 5/8
52 22 19 1/8 20 5/8
56 24 21 1/8 22 5/8
60 26 23 1/8 24 5/8
64 28 25 1/8 26 5/8
68 30 27 1/8 28 5/8
72 32 29 1/8 30 5/8
76 34 31 1/8 32 5/8
80 36 33 1/8 34 5/8
88 40 37 1/8 38 5/8
92 42 39 1/8 40 5/8

 *Jeld-Wen Lineal Part Number = W038H (White) W0381(Beige)

W1 DH Weatherstrip 

5/16" Bulb for Parting Stop

WO753

W2 DH Checkrail Weatherstrip

WK769

W3 DH Rail Weatherstrip - Foam Filled

WN940

W4 DH Sill Weatherstrip

Longest Lineal Part Number = WK755 (75 3/4")

DH Operators

Width Part # Cut Length
21 3/8" WK735 18 3/8"
25 3/8" WK736 22 3/8"
29 3/8" WK737 26 3/8"
31 3/8" WK738 28 3/8"
33 3/8" WK739 30 3/8"
37 3/8" WK740 34 3/8"
41 3/8" WK741 38 3/8"
45 3/8" WK742 42 3/8"

DH Pictures


Width Part # Cut Length
21 3/8" WK743 19 3/4"
25 3/8" WK744 23 3/4"
29 3/8" WK745 27 3/4"
31 3/8" WK746 29 3/4"
33 3/8" WK747 31 3/4"
37 3/8" WK748 35 3/4"
41 3/8" WK749 39 3/4"
45 3/8" WK750 43 3/4"
49 3/8" WK751 47 3/4"
53 3/8" WK752 51 3/4"
69 3/8" WK754 67 3/4"
77 3/8" WK755 75 3/4"

W5 Jamliner Head Foam Pad

W3085

W6 Clutch Pocket Plug - a.k.a. Doghouse Plug

W038O

*Use for both Old & New EX Jamliners
 Intek = Old
 Micron = New

W7 DH Jambliner Dust Plug

New Micron - W038N
Old Intek - WN090

J1 DH Oper. Head Parting Stop

Frame Width Part #
21 3/8" J27256
25 3/8" J27257
29 3/8" J27258
31 3/8" J27508
33 3/8" J27259
37 3/8" J27260
41 3/8" J27261
45 3/8" J27262
49 3/8" J27263

J2 DH Oper Side LIner Stop

Frame Height Part #
15" (T) J27547
18" (T) J27548
24" (T) J27549
32" J27550
36" J27551
40" J27552
44" J27553
48" J27554
52" J27555
56" J27556
60" J37557
64" J27558
68" J27559
72" J27560
76" J27561
80" J27563
84" J27563
88" J27564
92" J27565

J3 DH Picture Horizontal Sash Stop

Frame Width Part #
21 3/8" J272244
25 3/8" J27225
29 3/8" J27226
31 3/8" J27507
33 3/8" J27227
37 3/8" J27228
41 3/8" J27229
45 3/8" J27230
49 3/8" J27231
53 3/8" J27232
61 3/8" J27233
69 3/8" J27234
77 3/8" J27235
81 3/8" J27568

J4 DH Picture Vertical Sash Stop

Frame Height Part Number
15" (T) J27236
18" (T) J27237
24" (T) J27238
32"  J27239
36" J27240
40" J27241
44" J27526
48" J27242
52" J27243
56" J27244
60" J27245
64" J27246
68" J27247
72" J27248
76" J27249
80" J27250
84" J27251
88" J27252
92" J27253

J5 DH Picture Liner Stop

Frame Height Part Number
15" (T) J27527
18" (T) J27528
24" (T) J27529
32" J27530
36" J27531
40" J27532
44" 27533
48" J27534
52" J27535
56" J27536
60"  J27537
64" J27538
68" J27539
72" J27540
76" J27541
80" J27542
84" J27543
88"  J27544
92" J27545